Bently Nevada Trendmaster Pro Online Condition Monitoring System
Trendmaster® Pro is its innovative architecture, which links hundreds of permanently mounted transducers and measurement points onto a single-cable sensor network, and brings the data into System 1® software. Wiring costs are dramatically reduced when compared to a conventional continuous monitoring system, yet individual measurement points can be scanned by the system every few minutes to provide quasi-continuous condition monitoring data.
Pricing available upon request
Features and Benefits
Signal Processing Hardware
Compact, centralized signal processing stations, known as Dynamic Scanning Modules (DSMs) are strategically placed throughout your plant and accept from one to four sensor bus cables, resulting in a distributed network of condition monitoring sensors. All sensors on each bus are polled sequentially every few minutes, allowing the system to collect condition monitoring data from thousands of connected points, yet without the installation and hardware costs associated with traditional, centralized architectures relying on point-to-point wiring rather than a distributed bus.
Although the Trendmaster Pro System can accept signals from virtually any commercially available sensor or monitoring device, a wide range of special vibration, temperature, seal leak, pressure, and other sensors have been specially developed to complement the system. These sensors offer the ideal balance of robustness, ease-of-installation, and low cost, allowing the benefits of permanent monitoring while remaining highly affordable.
Unlike many other so-called “sensor bus” or “field bus” networks, the Trendmaster Pro system is specifically designed to handle the large bandwidth requirements of condition monitoring data—and requires just a single IS barrier or galvanic isolator for hundreds of points, allowing its use in hazardous areas without prohibitive installation costs.
DSMs can be connected directly to your process control system using industry-standard Modbus® protocol. This provides an extremely cost-effective entry-level system that uses your existing plant control platform for archiving, alarming, and display - resulting in a totally integrated condition monitoring and process control environment for your operators.
When more in-depth analysis capabilities are required, DSMs can also be connected to System 1 software via conventional wired or wireless Ethernet networks where all condition monitoring
data is archived and displayed. This allows your Trendmaster Pro installation to seamlessly integrate with portable data collectors and continuous monitoring systems, such as Bently Nevada Snapshot instruments and 3500 Series Machinery Protection Systems.
|Trendmaster Pro Brochure 1 MB||English|
|149744 Trendmaster Pro Data Sheet - 149831W 305 KB||English|
|Orbit Trendmaster Pro 758 KB||English|
1-3 of 3
Components & Accessories
Use the arrows below to view all  components and accessories for this product
Trendmaster 101284 Transducer Interface Module (TIM) Line Isolator
The 101284 TIM Line Isolator provides you with three galvanically-isolated Signal Processing...Download 259 KB
Trendmaster 162459-01 Galvanic Isolator
The Trendmaster® Galvanic Isolator enables the Trendmaster system to connect to intrinsically...Download 164 KB
Trendmaster 200125 Thermocouple
The 200125 temperature sensor is specifically designed to meet the needs of Trendmaster* 2000...Download 152 KB
Trendmaster 200150, 200155 & 200157 Accelerometers
The 20015x Accelerometers are general purpose, wide frequency, case-mounted seismic...Download 457 KB
Trendmaster 200200 proTIM-R Module
The 200200 dual-input proTIM-R (DIN rail mount) provides 2 channels of measurement.Download 693 KB
Trendmaster 200250 proTIM-C Module
The 200250 dual-input proTIM-C (conduit mount) provides 2 channels of measurement.Download 597 KB
Trendmaster 200350 and 200355 Accelerometers
The 200350 and 200355 Accelerometers are general purpose, casemounted seismic transducers...Download 559 KB
Trendmaster Dual Pressure flexiTIM System
The Dual Pressure flexiTIM* module interfaces 2 individual pressure transducers to the...Download 238 KB
Snapshot Trendmaster TIM Tester
The Snapshot* TIM Tester is a verification and configuration tool for use with Bently Nevada*...Download 280 KB
GE Updates XL Series of Video Borescopes for Remote Visual Inspection
New feature updates to versatile, industry-proven utility VideoProbe™
GE Brings Digital Solutions to Nondestructive Testing (NDT) Industry
Mentor UT™ Improves Productivity with the Power of Apps and Live Wireless Collaboration...
GE Releases Advanced Calibrator and HART/Foundation Fieldbus Communicator to Provide Greater Productivity in Hazardous Areas in the Process Industry
Latest Intrinsically Safe Druck DPI620 Genii IS offers world-class measurement and calibration with ATEX and IECEx Approvals
GE Strengthens OT Environments with IEC Cyber Security Standards
Leading industrial control solutions now compliant with IEC 62443-2-4 standards for enhanced security
Looking for software, a brochure, or a manual?
Visit the download center to find documents and software related to our products.
Contact us to learn more about how we are transforming the future of industry with our digital products, software and service solutions.